产品分类
联系我们
cisco WIC-1B-S-T-V3 V01产品介绍
cisco WIC-1B-S-T-V3 V01思科原装线卡模块
This document provides the technical specifications and cable requirements for the WIC-1B-S/T and WIC-1B-U WAN interface cards.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
This document is not restricted to cisco WIC-1B-S-T-V3 V01思科原装线卡模块 specific software and hardware versions.cisco WIC-1B-S-T-V3 V01思科原装线卡模块
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.cisco WIC-1B-S-T-V3 V01思科原装线卡模块
WIC-1B-S/T Interface Card
The Integrated Services Digital Network (ISDN) Basic Rate Interface (BRI) WAN interface cards are shared between the Cisco 1600, 1720, 2600 and 3600 Series Routers. Each card supports a single ISDN BRI port offered with and without the NT1 interface.
The S/T WAN interface card module (WIC-1B-S/T) cisco WIC-1B-S-T-V3 V01思科原装线卡模块 needs the external Network Termination 1 (NT1) device whereas the U WAN interface card module (WIC-1B-U) has an internal NT1 device.
Cables
The WIC-1B-S/T interface card requires RJ-45 to RJ-45 straight-through cables (provided by the customer).
ISDN BRI S/T Port Pinouts
The table below shows the ISDN BRI S/T port pinouts (RJ-45).
8 Pin1 | TE2 | NT3 | Polarity |
---|---|---|---|
3 | Transmit | Receive | + |
4 | Receive | Transmit | + |
5 | Receive | Transmit | - |
6 | Transmit | Receive | - |
1Pins 1, 2, 7, and 8 are not used.
2TE refers to terminal terminating Layer 1 aspects of TE1, TA, and NT functional groups. This applies to the Cisco 1603 and the ISDN BRI S/T WAN interface card.
3NT refers to network terminating Layer 1 aspects of NT1 and NT2 functional groups. This applies to the Cisco 1604 ISDN S/T port.
BRI S/T WAN Interface Card LEDs
The table below lists the BRI S/T WAN interface card LEDs and their meaning.
LED | Meaning |
---|---|
B1 | Active connection on B1 channel |
B2 | Active connection on B2 channel |
OK | ISDN port has established a connection with the central office switch |
WIC-1B-U WAN Interface Card
ISDN BRI U Port Pinouts (RJ-45)
The table below lists the ISDN BRI U port pinouts and their function.
8 Pin1 | Function |
---|---|
3 | No connection |
4 | Signal -- Tip or Ring |
5 | Signal -- Tip or Ring |
6 | No connection |
1Pins 1, 2, 7, and 8 are not used.
ISDN BRI U WAN Interface Card LEDs
The table below lists the ISDN BRI U WAN interface card LEDs and their meaning.
LED | Meaning |
---|---|
B1 | Active connection on B1 channel |
B2 | Active connection on B2 channel |
NT1 | NT1 has established a connection with the central office switch |
ISDN BRI Cable Specifications
The table below lists the ISDN BRI cable specifications.
Specification | High-capacitance Cable | Low-Capacitance Cable |
---|---|---|
Resistance (at 96 kHz) | 160 ohms/km | 160 ohms/km |
Capacitance (at 1 kHz) | 120 nF1/km | 30 nF/km |
Impedance (96 kHz) | 75 ohms | 150 ohms |
Wire diameter | 0.024" (0.6 mm) | 0.024" (0.6 mm) |
Distance limitation | 32.8' (10 m) | 32.8' (10 m) |
1 nF = nanoFarad